![]() The example at the top of this article shows Mixes 1 and 2 aggregated together. Applies to: Saffire Range and 1st Generation Scarlett 6i6, 8i6, 18i6, 18i8 and 18i20 The first section of this MixControl tutorial is going to focus on the top half of the control panel (shown below), and how to use it to create custom mixes that can be routed to any of the outputs on your interface. Learning and Getting Started with Saffire Pro40 Mix Control After doing a computer reboot, you can access the mix control in Windows by going to Start > All Programs > Focusrite > Saffire MixControl, then click the Mix Control launcher. The mixes combine in the following way: Mix 1 with Mix 2 and vice versa, Mix 3 and 4, Mix 5 and 6, etc. However, the stereo button on the mix output aggregates that mix with the one next to it, and the mix tab at the top of the screen expands. a Channel Fader, and Mute, Solo, and Stereo buttons. The controls are essentially the same as those found in the mixer channels, i.e. The audio from the separate mix channels then goes to the mix output, which is situated at the right-hand end of the mixer section. It is also possible to name the channel by clicking in the box below the Mute and Solo buttons. Stereo – Aggregates the 2 mono channels together into a single stereo channel with shared controls.Preview the selected channel before the level is altered by the channel fader. Channel Fader – adjusts the level of the channel.Pan – adjusts the balance between left and right speakers.The inputs selected will be the same in each of the mixes, however, the other controls are specific to each mix. Inputs are all of the audio inputs on your interface (both analogue and digital), and DAW contains all of the audio channels being sent back to your interface from your computer (Digital Audio Workstation). The possible inputs are divided into streams grouped by source, as shown in the drop-down menu above. This is done by clicking in the box above the pan control in the channel, as shown below. The first thing that you need to do is to select an input for the channel. Let’s start by focussing on a pair of channels in the mix window: With the PRO 24 and PRO 24 DSP, this number is halved. When used with the PRO 40 and the Liquid Saffire 56 (pictured above), Saffire MixControl contains up to 16 mono or 8 stereo mixes. It is worth noting, however, that this section of the MixControl software has no effect on the signal being passed into your computer. The first section of this MixControl tutorial is going to focus on the top half of the control panel (shown below), and how to use it to create custom mixes that can be routed to any of the outputs on your interface. The H/W Control button (Saffire PRO 40, Liquid Saffire 56 and Scarlett 18i20 only) links the position of the monitor dial in the MixControl software to the position of the monitor level control on the front of the Saffire hardware.Applies to: Saffire Range and 1st Generation Scarlett 6i6, 8i6, 18i6, 18i8 and 18i20 ![]() However, all of these presets can be configured manually using the method described above. The Monitor Preset… button allows you to select a variety of preset speaker configurations, more information about which can be found on your product’s download's page. Care should be exercised so as not to damage any audio equipment connected to these outputs, as the audio will be very loudĬlicking on the individual outputs toggles them between blue and red, whereas holding down the SHIFT button on your keyboard and clicking will turn the output grey/silver. Saffire MixControl ultra-low-latency DSP mixer/router Provides an 18 x 6 DSP mixer with. Grey/Silver outputs are active and will output any audio at full volume, regardless of the position of the monitor level dial. De Saffire Pro 14 biedt 2x Focusrite award-winning mic preamps.Blue outputs are active, and their level is controlled by the monitor level dial in the MixControl software (shown in the screenshot above).Red outputs are muted, and no audio will be passed from them.They will either beRed, Blue, or Grey/Silver. This is achieved in the monitor section of MixControl, shown below:Ībove the Monitor Preset… button in the monitoring section of Saffire MixControl, you will be able to see numbered boxes corresponding to the line (analogue) outputs on your unit. Once you have configured your mixes and routed audio to the outputs of your Saffire (see Part I and Part II of this tutorial), you need to ensure that a sufficient level is getting to your chosen outputs. Applies to: Saffire Range and 1st Generation Scarlett 6i6, 8i6, 18i6, 18i8 and 18i20 Features High-quality 24-bit/96kHz FireWire interface Saffire MixControl ultra-low-latency DSP mixer/router Midnight Plug-in Suite (RTAS/AU/VST), Red 2 & Red.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |